Package Contents: 


1x Caster Unit

1x Wifi Card (Do Not Remove)

1x 5.0V/3.0A Power adaptor


You will need: 

2x audio input cables with Male XLR connectors

Network access via Wifi


Optional:

1x Ethernet Cable (for Wired Internet connections)

1x USB Flash Drive (MS-DOS (FAT32) - Preferably USB 3.0)

2x Audio output cables with Female XLR connectors


Getting Started


  1. Plug your audio input cables into the respective L-R sockets on the front face of the unit. (Consult Diagrams at the bottom of this document)


  1. If you are planning on using an ethernet connection to connect your Caster, run an ethernet cable from an active ethernet port on your network into the front face of the unit. (If you plan to connect your Caster via wi-fi, you can skip this step)


  1. Plug the Power supply into the front face of the unit. The red light on the rear face of the Caster will glow.


  1. Caster’s stream controls and settings are all managed via a web browser on either a desktop or mobile device. Head to your device’s WiFi settings and select the Picaster Network from the available networks (Picaster_ XXXXXX) 


Connect using the Password 1love4streaming


  1. In a browser window/app, visit picaster.ss while connected to the Caster network. You will arrive on the Login Page. Use the default login:  


Username: admin 

Password: p1c8st3r

  1. If you have not established an ethernet connection, you will be automatically directed to the network settings page where you can set up a wifi connection. Select your wireless network from the available list and input the network password.


If you are using an ethernet connection then you will automatically be connected to your network via DHCP


Profiles


To start streaming with Caster you will need to set up at least one Profile.


Profiles allow you to set the target mounts to direct your contribution stream. Multiple different profiles can be stored on the Caster to recall for future use. 


You can preload any available profile before streaming to configure the active target mount. (Caster can only stream to one target mount at any one time).


     1) Go to Profiles and select “Create a new profile”.

    

    2) Input the mount details for the target stream you wish to contribute to. 

Tip: If you are a SharpStream Portal user, you can find this information for any of your streams on the stream information page.


    3) Select the desired encoding format and bitrate of the stream you wish to send. 


    4) Select the reconnect setting of the profile. This configures the behaviour of Caster when the power is disconnected and reconnected.


If the reconnect setting is set to “recall last value”, Caster will startup with whichever stream status was set upon disconnection of the power supply. “Always On” will mean that the stream automatically connects upon reconnection of the power supply and “Always Off” will mean that the stream will always require manually reactivating upon power reconnection.


    5) Select your USB Recording preference to on or off (see Local Recording via USB for more information).


    6) Save your Profile. Once saved click “Activate” on the profiles page to apply the profile settings. You can have multiple profiles listed on this page but only one can be activated at any one time.


Streaming


Once you have activated your profile, you are ready to stream. Head to the Dashboard and click “Start” to connect.


The latency chart will give a live update of the delay-to-stream and the dB meter will indicate the volume of your audio output. These tools can help you diagnose any network or audio issues if they arise.


Local Recording via USB


Caster allows you to record your stream output directly to a USB flash drive, giving you a great quality recording of your session right away, wherever you are without the need for a secondary recording device. To do this, make sure you have a good quality USB drive. We recommend using a USB 3.0 drive to ensure the bounce down of your recording to the drive is speedy.


  1. Before streaming, plug your drive into the unused USB port on the front face of the unit. Ensure your Drive is formatted as MS-DOS (FAT32) Do not attempt to remove the card in the top port.

  2. Load a profile on Caster which has USB Recording enabled.

  3. Ensure the interface has indicated that the flash drive has been recognised before commencing your stream.

  4. Once the drive is recognised you are ready to begin streaming.

  5. Start your stream as usual. Caster will begin recording the stream output.

  6. When your streaming session has finished, stop the encoding instance and wait until prompted before removing the flash drive.

  7. Your recorded session file(s) will be saved to your drive under a folder named “recordings”


Login


To keep your encoder settings safe, PiCaster requires a login to access the configuration interface. On the first login, use the default login provided. We recommend changing your login to something memorable and making a note of it securely for future logins. To do this, go to logins and input your desired username and password. 


Unit Diagram: